Home > MISCELLANEOUS TOOLS > Glues and Wax
Sort By:
Page of 1
UN-Cure CA Debonder   1 oz BSI Insta-Cure+ Gap Filling 1/2 oz BSI Insta-Cure Thin 1/2 oz

This item is for store Pickup only. It will not be shipped

UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option. to apply.

This item is for store Pickup only. It will not be shipped

Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.

This item is for store Pickup only. It will not be shipped

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.read the CA out.

Quickwood Epoxy Pine Quickwood Epoxy Natural BSI Insta-Set CA Accelerator
Quickwood Epoxy Pine
List Price: $8.00
Our Price: $4.50
Savings: $3.50
Quickwood Epoxy Natural
List Price: $8.00
Our Price: $4.50
Savings: $3.50

QuikWood Epoxy Putty Stick is a hand-kneadable, fast-setting polymer compound for permanent repairs to wood. It also bonds to metal, glass, masonry and many plastics. It comes in a handy "Tootsie-roll®" form with the curing agent encapsulated in the contrasting color base material.

QuikWood Epoxy Putty Stick is a hand-kneadable, fast-setting polymer compound for permanent repairs to wood. It also bonds to metal, glass, masonry and many plastics. It comes in a handy "Tootsie-roll®" form with the curing agent encapsulated in the contrasting color base material.

This item is for store Pickup only. It will not be shipped

INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.

Insta-Cure IC-GEL Glue Tube MELTONIAN BOOT AND SHOE CREAM FASHION BROWN 140 MELTONIAN BOOT AND SHOE CREAM IVORY

This item is for store Pickup only. It will not be shipped

IC-GEL™ is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE™. IC-GEL™, however, can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL™ can be applied at any angle with just a squeeze of the tube. The gel does, however, have a tendency to continue to come out of the tube for about a second after pressure is released, so this must be taken into account to apply the exact amount of IC-GEL™ that you want.

IC-GEL™ is an excellent putty for plastic models. It will fill any void and can be formed to many shapes. Applying INSTA-SET™ allows IC-GEL™ to be sanded or filed to final shape in less than 20 seconds. Autobody repairmen have finished their jobs in a fraction of the time by using IC-GEL™ with the additional advantage over normal body putties of superior bonding to metal surfaces.

IC-GEL's™ most popular application is for the bonding of fragments of live coral (frags) to underwater rocks in aquariums. It has proven to be non-toxic to aquatic organisms and provides instant bonding for the propagation of the coral. IC-Gel has a superior shelf life of over three years and its application nozzle makes it the easiest of all CAs to apply.

A limited supply of Meltonian remains and being made available at comparable internet prices.  See options for colors available.  Some items may vary in cost. A limited supply of Meltonian remains and being made available at comparable internet prices.  See options for colors available.  Some items may vary in cost.